My Account  |  0 item(s)    View Cart
Home > BMS for Lithium Batteries
48V 18A-200A EV BMS
For 13 Lithium Li-NCM Battery Packs in Series (13S)
ECPC-Simple-BMS-48V-13S-Li-NCM
Review this item Review this item
48V 18A-200A EV BMS<br>For 13 Lithium Li-NCM Battery Packs in Series (13S)
Wiring Diagram - 48V 13S EV BMS (Battery Management System)
Email a friend Email a friend
Description

48V 18A, 25A, 35A, 45A,

60A, 100A, 120A, 150A, 200A

EV BMS (Battery Management System)

For 13 Lithium Li-NCM Battery Packs in Series (13S)

 

BMS Fundamentals Explained

 Instructions for Paralleling Strings of Batteries

 

CONSTANT

DISCHARGE

CURRENT

PEAK

DISCHARGE

CURRENT

MAX CHARGE CURRENT

OVER

CURRENT

PROTECTION

PRICE EACH

18A

50A

18A

None*

$16.00

25A

60A

25A

None*

$19.30

35A

100A

35A

None*

$21.00

45A

180A

45A

None*

$25.00

60A

180A

60A

None*

$30.00

100A

200A

100A

65A

$74.00

120A

350A

120A

65A

$94.00

150A

400A

150A

65A

$125.00

200A

400A

200A

65A

$157.00


*Can be customized

Price
Price with Options:
$0.00


(Discounts, if applicable, will show in the "Shopping Pallet")

48V 13S EV BMS (Battery Management System)
Amperage Needed?
Selection Required
Shipping Method?
If buying with batteries shipping will be quoted separately
Without batteries shipping costs $12 in the Continental USA
Delivery Date Needed? Enter it here:

Special Instructions? Enter them here:

Quantity

Features for the 48V 13S BMS:

  • Top Quality (A-level) Protective Circuit IC
  • Strong Load Ability, Constant Discharge Current, High Voltage Resistance, Low Inner Resistance Power Mosfet
  • IC itself has power balancing function. The circuit is simple and reliable.
  • Extremely Low Power Consumption. The consumption of the whole device is less than 50uA.
  • The PCB uses high anti-corrosion, high water resistance, and high impedance ESD conformal coating

 

Specifications for the 13S BMS:

 

CHARGE VOLTAGE

55.25V

OVER CHARGE PROTECTION VOLTAGE

4.25V

POWER BALANCE VOLTAGE

4.18V

BALANCE CURRENT

35mA

OVER DISCHARGE DETECT VOLTAGE

2.8V

SHORT CIRCUIT PROTECTION

External Load

Short Circuit

MAIN CIRCUIT RESISTOR

<10 milliohms

WORKING TEMP F (C)

-22 to 176

(-30 to 80)

 

Wiring Instructions


Common Port - Separate Port - Simple BMS Wiring Diagrams 

First, Preparation before installation

Make sure the batteries are of a good consistency, the voltage difference is no more than 0.05V, the inner resistance is no more than 5 milliohms, and the capacity difference is lower than 30mAh. Connect the batteries in parallel first and then in series. The better the battery consistency is, the higher the performance of the BMS.

 

Second, Wiring instructions

Attention: Please use our wires for our BMS. Don’t use other factories’ wires because they don’t match up with our BMS.

 

Step 1, B-(blue thick wire): Connect to battery pack total negative pole –

 

Step 2, Disconnect the wires for batteries from the BMS side.

 

Step 3, Connect the wires to batteries. Start from the thick black wire to total negative pole (B1-), then connect the 2nd red thin wire to the 1st battery positive pole (B1+) B2+, B3+, B4+ … till the last red thick wire.

 

Step 4, When you are finished connecting all the wires to each battery, don’t plug into the BMS directly. We suggest you use a multimeter to measure the voltage of two adjacent metal terminals (You can see the white connector with silver metal pins on the BMS). If the voltage is 3.0~4.2V (LiNCM), 2.0~3.6V (LiFePO4), 1.5~2.75V (LTO), then the wiring is correct.

 

Step 5, Ensure the wires are connected to the batteries correctly and the voltage is normal. Then you can plug the wires into the BMS.

 

Step 6, P-: Connect P-(black thick wire) to load – and charger –

(if you ordered “common port”).

 

Charger+ connect to C-(yellow wire) load+ connect to P-(black thick wire)

(if you ordered “separate port”).

 

Step 7, charger+ and load+ connect to battery+. Please use thick wire.

 

Third, Measure the total voltage of the pack and the output voltage of the BMS. If the voltage is the same, it means the wiring is correct. You can use the BMS now. Otherwise please check the wiring again according to the tips above.

 

 

Frequently Asked Questions about the BMS/PCB

 

1, Which current PCB should I use?

Take a 13S 48V pack as an example: Which PCB you should use depends on the power of your motor or the current limitation of your controller. Below 350W, you can use 16A. Below 500W, you can use 18A, Below 800W, you can use 35A, Below 1KW, you can use 60A. Above 1200W, the same. If you are not sure, please contact us.

 

2, Can I use a bigger size of PCB than is indicated?

Suppose you need 60A PCB but you chose 80A, that will work.

80A allows for a higher current. A bit higher price is the only drawback.

But if you choose 50A, it will be too small. So you can use a higher spec but not a lower one than it should be.

 

3, What kind of charger should I choose?

A Lithium Battery must be charged by a Lithium Battery Charger. You can’t charge it with a lead acid battery charger because the lead acid battery charger might damage the MOS pipe of the PCB.

 

4, if I have a PCB, do I need any balancers?

Yes if you add QNBBM balancers, that will be perfect.

The Main function of the PCB is to prevent batteries from over-charging over-discharging, over-heating etc.

With balancers added, the batteries lifespan will be longer and the capacity will get fully used.

 

5, How do I judge if my PCB is broken or not?

If you’d like to judge if the PCB is fine or not, please use a multi-meter and see if the voltage of each cell is close to one other or not. When the voltage difference is 1V, the battery will have this kind of performance: the driving distance will be short, it will be cut off when started, the charging time will be very short. Under such a situation, a battery is defective. When the PCB is broken, the battery can’t be discharged. When you measure the battery voltage, it will be normal.


 

      

* SHIPPING/PAYMENT OPTIONS *

 

There are 2 ways to get an exact quote for the base shipping for your 48V 13S EV BMS (Battery Management System) order.

1.  Contact us at (801) 449-0681 9am-5pm Monday-Friday or email info@electriccarpartscompany.com or go through our Contact Us page

 

Or

 

2. Place your order by clicking in the shopping pallet “Proceed To Checkout”

a. Enter your information so we can get you a shipping quote

b. Select the “Shipping Method” of preference

c. Confirm the “Choose one payment method” has “Shipping Quote Request” selected

d. Click the “Check Out” button

e. You’ll receive a confirmation email of your request, as will we

 

We’ll research the exact shipping cost and send you an invoice to your PayPal or email or you can add it to your pallet in $1 Shipping Increments for your 48V 13S EV BMS (Battery Management System) order.

 

 

Quantity discounts show in the “Shopping Pallet”.

 

We love to meet or beat any competitor’s price!

 

Higher volume discounts, price matching or questions?

Contact Carl, our resident specialist.

9am-9pm Mon-Sat MDT

(801) 449-0681

or email

Carl@ElectricCarPartsCompany.com

Or

info@ElectricCarPartsCompany.com

or through our Contact Us page

Related Items
24V-25.6V-28.8V<br>8 Cell-Battery Series<br>UL, SGS and UKAS Certified<br>PCB-PCM
24V-25.6V-28.8V
8 Cell-Battery Series
UL, SGS and UKAS Certified
PCB-PCM
Specification of Battery Balancer
Specification of Battery Balancer
12V 45A-200A EV BMS<br>For 4 Lithium LiFePO4 Battery Packs in Series (4S)<br>USA Stock!
12V 45A-200A EV BMS
For 4 Lithium LiFePO4 Battery Packs in Series (4S)
USA Stock!
Browse Similar Items
BMS for Lithium Batteries > - SIMPLE LITHIUM BMS - Li-NCM - MOBILE