Electric Car Parts Company
Specializing in Lithium Batteries, Chargers, Solar Storage
Features:
· The ME102 is a 10-inch DC-Series motor capable of a continuous current of 200 amps, and 550 amps for 2 minutes.
· Efficiency up to 93%.
· 26 KW (35 HP) continuous, and 63 KW (84 HP) peak.
· Motor Weighs 190 pounds. Motor in the shipping crate is 203 Pounds. The motor is shipped on a pallet measuring a total of 48 x 40 x 30, weighing a total of 240 pounds.
· 1 year manufacturer’s defects warranty.
DC Voltage
Current
(Amps)
Speed
(RPM)
Torque
NM (Ft Lbs)
Power
KW (HP)
Efficiency
(%)
48
300
1275
90.25 (66.5)
11.2 (15.0)
78
250
1400
70.23 (51.8)
9.7 (13.0)
81
220
1520
59 (43.5)
8.6 (11.6)
82
205
1700*
54.11 (39.9)
8.2 (10.9)
83
180
1780
44.8 (33)
7.2 (9.6)
170
1850
42.38 (31.3)
6.8 (9.0)
72
1938.4
18.3 (24.5)
2119.2
15.6 (20.9)
84
2240
13.8 (18.5)
86
2329.6
13.2 (17.7)
88
2472.8
11.6 (15.5)
2560
11.4 (15.3)
90
2423
22.9 (30.7)
84.8
2649
19.48 (26.1)
86.6
2800
17.3 (23.2)
87.4
2912
16.5 (22.1)
89.4
3091
14.5 (19.4)
89.5
3200
14.2 (19.0)
92.8
144
3876
36.6
85
4238
31.2
87
4480
27.7
4659
26.4
4945
23.2
5120
22.7
93
Note:
Data at 72 and 144 VDC is estimated. Data at 48 and 90 VDC is actual data taken on a Dynamometer using a hard (constant) voltage supply.
Wiring Instructions:
1) (B-) to A, FF to (B+), and jumper AA to F. It runs CCW on the drive end.
2) The two pins are a Brush Life Indicator. It is made to run to a light bulb that will turn on when the brushes get too low. Notice that full motor voltage will be across the two wires when the Brushes get too short.
3) The two wires are a temperature sensor. It is normally open. This is the same type of warning as the brush life indicator. You can set a light to come on when the motor gets too hot in the windings or run it to the motor control for temperature feedback.
4) (B-) to A, F to (B+), and jumper AA to FF. It runs CW on the drive end.
5) The motors come with a Brush Timing set for maximum efficiency at 72 VDC in the CCW direction (LAS - Looking At the motor Shaft). See the picture of the Brush Holder in the pictures section above. Notice that there are slots in the base for the mounting bolts. You will need to rotate the Brush Holder in the opposite direction (same amount from center position) for maximum efficiency in the CW direction.
* SHIPPING/PAYMENT OPTIONS *
There are 2 ways to get an exact quote for the base shipping for your 48V, 72V, 90V, 144V, 550A, DC ME102 Double-Shafted Motor order.
1. Contact us at (801) 449-0681 9am-5pm Monday-Friday or email [email protected] or go through our Contact Us page
Or
2. Place your order by clicking in the shopping pallet “Proceed To Checkout”
a. Enter your information so we can get you a shipping quote
b. Select the “Shipping Method” of preference
c. Confirm the “Choose one payment method” has “Shipping Quote Request” selected
d. Click the “Check Out” button
e. You’ll receive a confirmation email of your request, as will we
We’ll research the exact shipping cost and send you an invoice to your PayPal or email or you can add it to your pallet in $1 Shipping Increments for your 48V, 72V, 90V, 144V, 550A, DC ME102 Double-Shafted Motor order.
Quantity discounts show in the “Shopping Pallet”.
We love to meet or beat any competitor’s price!
Higher volume discounts, price matching or questions?
Contact Carl, our resident specialist.
9am-9pm Mon-Sat MDT
(801) 449-0681
or email
[email protected]
or through our Contact Us page